Millimeter-wave Frequency Band Research Articles

Characteristic mode based self isolated MIMO antenna design for millimeter wave 5G communications

The paper introduces a self-isolated quad-port multi input multi output antenna system designed for fifth-generation wireless communication. The reported antenna structure possesses an overall dimension of 12.4 × 12.4 × 0.508 mm3 and is derived from a single-element antenna, featuring a circular patch accompanied by a sectoral slot. To achieve the desired frequency band, an additional circular patch is purposefully placed over the main radiator. The development of each design stage in the antenna structure is investigated using the theory of characteristic mode. This configured multi-element antenna structure achieves a broad operational bandwidth spanning 4.5 GHz, encompassing frequencies from 26.1 GHz to 30.6 GHz, rendering the antenna well-suited for deployment in the millimeter-wave frequency bands of n257, n258, and n261 respectively. A total gain of 6.27 dBi is achieved with port isolation of −24 dB. Furthermore, the antenna undergoes validation for diversity metrics, including envelope correlation coefficient, diversity gain, channel capacity loss, total active reflection coefficient, and mean effective gain. The antenna is fabricated and experimentally validated with the simulated counterpart. Later, a comparative analysis has been conducted which revealed that the proposed antenna demonstrates > 80 % increase in compactness compared to existing antenna designs documented in the literature.

Surface wave communication-based wave guide design concerns for flip chip package-based integrated circuits with bump pitch sizes of 1.2 mm and above

ABSTRACT The flip chip package (FCP) based integrated circuits supports millimetre wave frequency range (30 - 300 GHz), analysing the conditions for optimal signal transmission between the integrated circuits for FCP type being the primary essence of this article. The effective signal transmission occurs through a dielectric-coated conductor structure based on the surface wave communication phenomenon, known as a surface wave communication-based wave guide (SWW). The article focuses primarily on design considerations to build SWW for FCP applications at millimetre wave frequency ranges. The efficiency of the proposed waveguide was investigated in terms of power transmission capacity, voltage standing wave ratio (VSWR) and signal attenuation. The analysis comprises examining these parameters at the frequency range of 50 GHz to 150 GHz while taking into account varied degrees of waveguide dimensions and surface reactance. The measured results show that at the signal frequency of 100 GHz with dielectric and conductor thickness of 0.2 mm and surface reactance of 100 Ω, the suggested waveguide provides efficient signal transmission with approximately 0 dB signal attenuation, ideal high-power flow of 41,000 VA m 2 and VSWR of 1.2. Overall, this article provides insights on the design and performance of SWW for FCP applications at millimetre wave frequency band.

Ultra-broad band plasma–graphene absorber at millimeter-wave frequency bands

This paper introduces a new absorber that can effectively absorb millimeter wave frequencies. The design involves stacking foam, plasma, and laminated graphene sheets on a perfect electric conductor substrate. The absorber can generate a wideband effect on electromagnetic waves by combining graphene layers and a plasma medium. The absorption and bandwidth of the plasma slab depend on various parameters like plasma frequency, collisional rate, and thickness. By tuning the plasma frequency ωp (rad/s), average collision frequency υp(Hz), Fermi energy of graphene sheets, and thickness of the foam and plasma layers, the benefit of wideband and good absorption considering reflection amplitude lower than −15 dB, an ultra-bandwidth from 32 to 150 GHz can be achieved. This structure has multiple layers that have bandgap and band-stop regions. These regions are associated with the cavities of dielectric slabs that have graphene sheets. These regions are identified as coupled Fabry–Pérot resonances, which can induce multiple interference effects in multi-reflection for the incident electromagnetic waves, resulting in high-level absorption. Understanding and controlling these resonances is crucial for optimizing the performance of such systems. An equivalent circuit model has been used to predict the absorber's performance. The proposed absorber has a symmetrical structure that reacts similarly to transverse-electric and transverse-magnetic waves. The frequency range of the absorber has been studied to determine the effects of the graphene sheets' relaxation time and voltage biasing. The absorber offers advantages such as being thin, having a wide bandwidth, and being insensitive to polarization.

Multi-band passive detection and imaging system for concealed weapon with dual assessment method

Technological advancements in the millimeter-wave (MMW) and terahertz (THz) frequency bands have seen rapid progress, especially in the field of concealed weapon detection. The capability to detect concealed objects under clothing without causing harm to individuals is of utmost importance. Because of this reason, the concept of the variable target ranges in a passive MMW/THz imaging system with the infrared band has been studied in detail. An imaging system, called multi-band passive detection and imaging system (MIS) in this study, with variable target ranges, was designed and tested. A passive MMW/THz imaging system is developed specifically for concealed weapon detection, with a primary focus on variable target ranges. In addition to this, an infrared imaging system has been incorporated into the concept of concealed weapon detection. To integrate these two imaging systems, image fusion techniques have been employed as a conjunction between them. Detailed analyses have been conducted to assess the concealed weapon detection capabilities of this integrated system. The image fusion results, combining infrared and passive MMW/THz bands, have been tested at variable target ranges, and the fused images have been compared in terms of structural similarity index (SSIM) and contrast levels (CL). The SSIM alone is an inadequate method in the concept of concealed weapon detection. The CL method, used with SSIM, eliminates the shortcoming of the SSIM alone. The outcomes of these tests demonstrate that MIS enhances the detectability of concealed weapons with the use of SSIM and CL together. As a result, this study lays a solid foundation for the future detection of concealed objects beneath clothing. The dual assessment method proposed in this study will enable the development of new methods that will increase the detection of specific objects under the clothes in the future.

A novel SIGGW dual post band-pass filter for 5G millimeter-wave band applications with a transmission zero

Integration of planar circuits been considered a credible technique for low-cost mass production of microwave and millimeter-wave circuits and systems. For the first time, in this research a dual-post band-pass filter is designed and simulated in a three-layer substrate integrated gap groove waveguide (SIGGW) for 5G millimeter-wave frequency band applications. The filter includes 12 posts (6 times 2). Also, the structure facilitates to use resonant posts and so we can design the posts to add a transmission zero in lower rejection band. The design theory algorithm and its limitations are investigated based on the circuit model of filter. The results shows that FBW of 5% and a lower band transmission zero for the proposed 12 posts filter. Also, the results are verified by simulation using CST. According to the results, the proposed filter is a good option for Ka-band applications and can be used as the building block for suppressing the LO leakage that is commonly used for up-converting the 5G signal to Ka band.

A symmetric T-H shape wideband negative index metamaterial for 28-GHz millimeter-wave applications

One of the leading candidates for the next fifth generation of (5G) and body-centric wireless communications is millimeter-wave frequencies. In this study, a wideband tunable metamaterial (MTM) consisting of T-H shaped symmetric resonator is presented for body-centric applications operating in the millimeter-wave frequency band centered at 28 GHz. The characteristics of the proposed MTM are examined through wave propagation in both Z and X directions. It has a wide operating frequency range of 5.6 GHz for waves travelling along the Z-axis, with DNG characteristics at 26.2 GHz resonance frequency. However, it represents a negative epsilon metamaterial (ENG) range during X-axis wave propagation in the 25–29.4 GHz frequency range. The metamaterial is constructed on a Rogers (RT-5880) substrate and has a compact size, with overall dimensions of 0.420 λo × 0.420 λo. A proposed Y-shaped antenna is developed with a compact size of 1.36 λo × 1.82 λoto cover the 5G at 28 GHz. The single-Y-shaped antenna consists of aradiating patch, Rogers substrate, full ground plane, air bandgap (ABG), and array of DNG MTM.Thus, the array of MTM has been applied to validate the effect in the overall antenna performance such as gain which has been increased from 5.5 dBi to 8.5 dBi. The experimental, simulated results, and equivalent circuit model using Advanced Design Software (ADS) for validation functions showed that the completed results are comparable. The proposed mm-wave metamaterial is expected to be a good candidate for modern 5G wireless communication system components, especially to enhance the antenna gain and isolation. The proposed antenna loaded with MTM is a suitable contender for the upcoming 5G mm wave mobile handheld devices.

Loop-Type Field Probe to Measure Human Body Exposure to 5G Millimeter-Wave Base Stations

This paper proposes a field probe to measure the power density (PD) at a millimeter-wave (mmWave) frequency band. The proposed probe is composed of a loop antenna in which one end is terminated with a load resistor. Such a structure enables the simultaneous measurement of electric (E)- and magnetic (H)-fields: the E-field is measured at a gap where the load resistor is placed, and the H-field is measured through the loop antenna. The simultaneous measurement makes it possible to measure PD for an incident wave even in the near field region where the E- and H-fields have different phases from each other. The proposed probe is fabricated and evaluated for its PD measurement performance. The measurement results show that the probe measures PD with an error less than 1.3 dB. Owing to the near field measurement, the proposed probe is useful in measuring the human body exposure to electromagnetic fields (EMFs) that are generated by 5G mmWave base stations.

A compact bent microstrip-based wideband millimeter wave MIMO antenna for 5G applications

Abstract This paper proposes a wideband four-element multiple-input multiple-output (MIMO) antenna operating in the millimeter-wave frequency band for 5G communications from 24.37–39.44 and 45.09–50.62 GHz. The antenna design has been realized using Rogers 5880 substrate and consists of a T-shaped strip that is attached to the top of a 50 Ω feeding line. Two microstrip lines are affixed at the terminal points of T-shaped strip and bent toward the feeding structure. These bent strip lines are then extended by joining two additional L-shaped microstrip lines. On the back, there is a partial defective ground plane featuring a rectangular slot and a thin strip line located at its center. The dimensions of the proposed single element and MIMO antenna are 0.933λ × 0.933λ × 0.024λ and 1.865λ × 1.865λ × 0.024λ, respectively (at 28 GHz), while the edge-to-edge distance between the radiation elements of the MIMO antenna is 4.0 mm. The design incorporates an efficient passive fan-shaped decoupling structure to decrease coupling between antenna elements. Simulations and experimental results show good agreement with each other. For all resonant frequencies the measured peak gain is greater than 4.85 dBi, radiation efficiency is over 90%, diversity gain is greater than 9.5, ECC is less than 0.025, TARC is less than -10 dB and CCL is below 0.4 bits/s/Hz. The proposed MIMO antenna, with its wide bandwidth, high gain, high inter-port isolation, and high efficiency characteristics, can be used for 5G wireless communication applications.

Link-Level Simulator for 5G Localization

Channel-state-information-based localization in 5G networks has been a promising way to obtain highly accurate positions compared to previous communication networks. However, there is no unified and effective platform to support the research on 5G localization algorithms. This paper releases a link-level simulator for 5G localization, which can depict realistic physical behaviors of the 5G positioning signal transmission. Specifically, we first develop a simulation architecture considering more elaborate parameter configuration and physical-layer processing. The architecture supports the link modeling at sub-6GHz and millimeter-wave (mmWave) frequency bands. Subsequently, the critical physical-layer components that determine the localization performance are designed and integrated. In particular, a lightweight new-radio channel model and hardware impairment functions that significantly limit the parameter estimation accuracy are developed. Finally, we present three application cases to evaluate the simulator, i.e. two-dimensional mobile terminal localization, mmWave beam sweeping, and beamforming-based angle estimation. The numerical results in the application cases present the performance diversity of localization algorithms in various impairment conditions.

Reconfigurable Intelligent Surfaces: Performance Assessment Through a System-Level Simulator

Reconfigurable intelligent surfaces (RISs) are considered a promising technology for boosting the coverage and for enhancing the spectral efficiency of wireless systems, as well as for taming the wireless environment. The potential benefits of RISs are currently being analyzed and various approaches are being proposed to address the challenges for their integration in wireless networks. Currently available studies to quantify the potential gains of deploying RISs in wireless networks are limited to simple network topologies, while no system-level assessments have been reported to date. Network-level, e.g., on the scale of hundreds of square meters, simulations are, however, the first step to quantify the actual value of emerging technologies and the steppingstone before considering large scale system-level experimental evaluations and network deployments. Towards this direction, this article reports the first system-level simulation results and analysis of an RIS deployment in a typical urban city that is served by a fifth-generation cellular network. The obtained system-level simulation results unveil that the benefits of RISs vary depending on the operating frequency and the size of the surfaces. Specifically, we investigate the performance improvement that RISs can provide, in terms of outdoor and indoor coverage and per resource block rate, when deployed in mid (C-band) and high (millimeter-wave) frequency bands. For example, the obtained results unveil that the deployment of RISs enhances the coverage probability from 77% to 95% in the Cband and from 46% to 95% (92% in the

Deep Learning TCP for Mitigating NLoS Impairments in 5G mmWave

5G and beyond 5G are revolutionizing cellular and ubiquitous networks with new features and capabilities. The new millimeter-wave frequency band can provide high data rates for the new generations of mobile networks but suffers from NLoS caused by obstacles, which causes packet drops that mislead TCP because the protocol interprets all drops as an indication of network congestion. The principal flaw of TCP in such networks is that the root for packet drops is not distinguishable for TCP, and the protocol takes it for granted that all losses are due to congestion. This paper presents a new TCP based on deep learning that can outperform other common TCPs in terms of throughput, RTT, and congestion window fluctuation. The primary contribution of deep learning is providing the ability to distinguish various conditions in the network. The simulation results revealed that the proposed protocol could outperform conventional TCPs such as Cubic, NewReno, Highspeed, and BBR.

Design and Development of Multibeam Antenna Technologies for 5G Wireless Communications

Multibeam antenna (MBA) systems operating in the millimeter-wave frequency bands have drawn significant attention from researchers and are being effectively studied due to the demanding system needs for the fifth-generation (5G) wireless communication systems and the drastic spectrum scarcity at the existing cellular frequency range. To enable a greater transmission speed, an enhanced signal-to-interference-plus-noise ratio, an enhanced spectral and energy performance, and flexible beam shaping, they serve as the primary antenna technology. They offer tremendous potential for serving as the crucial infrastructure for facilitating beamforming and massive multiple-input multiple-output (MIMO) which uplift the 5G. To achieve this, a novel beamforming design and optimization approach based on the Convex Time Modulated Particle Swarm Optimization (CTM-PSO) algorithm is suggested for 5G communication networks, offering multiple concurrent transceivers to support efficient beamformed interactions whereas a second beam concurrently detects the atmosphere around the base-station. The suggested beamforming method combines the optimization of the transmitter and receiver beamforming weights to increase sensor performance, reduce potential intervention resulting from the communication beams, and ensure the communications link's target beamforming gains. Comprehensive numerical assessments are used to evaluate the effectiveness of the recommended method, showing that it may provide significant improvements over more conventional beamforming methods.

A novel metasurface lens antenna design for over‐the‐air testing in millimetre wave radio resource management measurement

AbstractIn millimetre wave (mmWave) frequency band, radio resource management (RRM) performance is characterised in plane wave conditions using radiated over‐the‐air test method, which is a challenging combination of protocol and radio frequency performance measurement. This article presents a novel design of multiple lens‐based compact antenna test ranges (CATRs) to simulate multiple angles of arrival from different base‐stations in RRM measurement. Only four lens‐based CATRs are proposed to create plane wave conditions at the device under test with six different angles of arrival and capable of accurately constructing the wireless propagation condition and minimising the diffraction and scattering between adjacent CATRs. The lens‐based CATR is the key element in the RRM measurement system, which is composed of a metasurface lens for phase alignment and a 2 × 2 feed array antenna for the emission of electromagnetic signals. The function and capability of the proposed lens‐based CATR is validated through simulation and measurement, that the worst‐case amplitude variation in the quiet zone region is lower than ±0.8 dB at 26 GHz, and phase variation is lower than ±7.5° in the designed quiet zone, which could be used in the fifth‐generation mmWave RRM measurement.

Five-Band Millimeter-Wave Antenna of Circular/Linear Polarization for Forthcoming Generations of Mobile Handsets

A compact planar antenna is proposed to operate in five millimeter-wave frequency bands at 28, 51, 55, 59, and 63 GHz. The antenna is designed to produce circular polarization at 28 GHz and linear polarization at the other four frequencies. The 28 GHz frequency band is recommended for long range communications, whereas the other four frequencies are recommended for short range communications due to the atmospheric absorption in this range of the millimeter-wave frequencies and to provide more secure communications. The reasons behind the selection of the specific values of the higher frequency bands (51, 55, 59, and 63 GHz) are (i) to provide enough number of multiple bands at such unlicensed frequency range to be used as alternatives for different applications, (ii) to give about 4 GHz separation between the center frequencies of each band and, (iii) finally, to avoid the operation at 60 GHz, in particular, due to the peak atmospheric absorption of millimeter-wave encountered at this frequency. The antenna is constructed as a square patch surrounded by five parasitic elements that are capacitively coupled to the square patch so as to realize the location of the resonant frequencies of the higher frequency bands. The antenna is fabricated and its performance is experimentally evaluated. The proposed antenna is shown to operate efficiently over the five frequency bands 28, 51, 55, 59, and 63 GHz providing impedance matching bandwidths of 2.0, 0.9, 1.2, 1.1, and 1.6 GHz, respectively. The corresponding values of the maximum gain are 7.0, 6.8, 6.0, 6.0, and 8.0 dBi, respectively. Also, the corresponding radiation efficiencies are 90, 90, 91, 78, and 86%, respectively. The 3 dB-axial ratio bandwidth at 28 GHz is about 1.2 GHz.

Carbon Nanotube Diodes Operating at Frequencies of Over 50GHz.

Radiofrequency (RF)diodes used for fifth and sixth-generation (5G and 6G) mobile and wireless communication networks generally require ultrahigh cut-off frequencies and high integration densities of devices with different functions on a single chip and at low cost. Carbon nanotube diodes are promising devices for radiofrequency applications, but the cut-off frequencies are still far below the theoretical estimates. Here, a carbon nanotube diode that operates in the millimeter-wave frequency bands and is based on solution-processed, high-purity carbon nanotube network films is reported. The carbon nanotube diodes exhibit an intrinsic cut-off frequency over 100GHz and the as-measured bandwidth can exceed 50GHz at least. Furthermore, The rectification ratio of the carbon nanotube diode by approximately three times by using yttrium oxide for local p-type doping in the diode channel is improved.

Persistent Homology Approach for Human Presence Detection from 60 GHz OTFS Transmissions.

Orthogonal Time Frequency Space (OTFS) is a new, promising modulation waveform candidate for the next-generation integrated sensing and communication (ISaC) systems, providing environment-awareness capabilities together with high-speed wireless data communications. This paper presents the original results of OTFS-based person monitoring measurements in the 60 GHz millimeter-wave frequency band under realistic conditions, without the assumption of an integer ratio between the actual delays and Doppler shifts of the reflected components and the corresponding resolution of the OTFS grid. As the main contribution of the paper, we propose the use of the persistent homology technique as a method for processing gathered delay-Doppler responses. We highlight the advantages of the persistent homology approach over the standard constant false alarm rate target detector for selected scenarios.

Performance Assessment and Comparison of Deployment Options for 5G Millimeter Wave Systems

The roll-outs of fifth-generation (5G) New Radio (NR) systems operating in the millimeter-wave (mmWave) frequency band are essential for satisfying IMT-2020 requirements set forth by ITU-R in terms of the data rate at the access interface. To overcome mmWave-specific propagation phenomena, a number of radio access network densification options have been proposed, including a conventional base station (BS) as well as integrated access and backhaul (IAB) with terrestrial and aerial IAB nodes. The aim of this paper is to qualitatively and quantitatively compare the proposed deployments using coverage, spectral efficiency and BS density as the main metrics of interest. To this end, we develop a model capturing the specifics of various deployment options. Our numerical results demonstrate that, while the implementation of terrestrial relaying nodes potentially improves coverage and spectral efficiency, aerial relays provide the highest coverage, three times that of a direct link connection, and also significantly reduce the required BS density. The main benefit is provided by the link between the BS and the aerial relay. However, gains are highly dependent on a number of elements in antenna arrays and targeted outage probability. The use of terrestrial relays can be considered a natural trade-off between coverage and the aggregate rate.

Gap Waveguide Technology: An Overview of Millimeter-Wave Circuits Based on Gap Waveguide Technology Using Different Fabrication Technologies

With the fast development of next-generation wireless communication and radar sensing, the millimeter-wave frequency band is becoming more and more important due to its rich spectrum, wide bandwidth, and ability to support the miniaturization of antennas and circuits <xref ref-type="bibr" rid="ref1" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">[1]</xref> , <xref ref-type="bibr" rid="ref2" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">[2]</xref> , <xref ref-type="bibr" rid="ref3" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">[3]</xref> , <xref ref-type="bibr" rid="ref4" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">[4]</xref> . High-performance, low-loss, and low-cost millimeter-wave circuits and modules are the key elements for wireless front-end systems. For planar transmission lines, such as microstrip lines and coplanar waveguides, they are very easy to integrate with other circuits for low-cost and low-profile physical designs. However, the high insertion loss and radiation loss from planar transmission lines limit their applications at the millimeter-waveband. As for rectangular and cylindrical waveguides, their main application is in the areas of low loss and high power handling, but their 3D structure is difficult to integrate with other planar passive and active circuits. The substrate-integrated waveguide (SIW) is a better way to merge the advantages of planar transmission lines and rectangular waveguides, but it still suffers from dielectric losses at the millimeter-wave frequency range.

Multifunctional Frequency Selective Absorber Enabling FR1 and FR2 5G OTA Tests in a Hybrid Reverberation Chamber

Due to the special advantages of the reverberation chamber (RC), it has been recognized as a standardized over-the-air (OTA) testing methodology by the cellular telecommunications industry association (CTIA). Currently, OTA tests of the fifth-generation (5G) wireless terminals are usually performed in different testing environments, e.g., in a reverberation chamber for fast isotropic tests in the sub-6 GHz frequency band, and in an anechoic chamber for directional tests in the millimeter-wave (mm-wave) frequency band, which are inconvenient and costly. In this work, two multi-functional frequency selective absorbers (FSAs) are designed to realize absorption in the 5G mm-wave band and reflection/transmission in the sub-6 GHz band. By loading the FSAs to the RC, an integrated testing environment for 5G terminals can be established. Namely, a quasi-anechoic environment in the mm-wave band and a reverberation environment in the sub-6 GHz band can be simultaneously achieved in the RC loaded with the proposed FSAs. Experimental and simulated results are presented to demonstrate the effectiveness of the proposed scheme.

Robust Design of 3D-Printed W-Band Bandpass Filters Using Gap Waveguide Technology

In this paper, a W-band 3D-printed bandpass filter is proposed. The use of higher-order TE10n modes in groove gap waveguide (GGW) technology is evaluated in order to alleviate the manufacturing requirements. In addition to the use of higher-order modes, the coupling between them is analyzed in detail to improve the overall fabrication robustness of the component. This allows the implementation of narrow-band filters operating at millimeter-wave frequency bands (or above), which usually demand complex manufacturing techniques to provide the high accuracy required for this kind of devices. In order to show the applicability of the proposed method, a narrow-band 5th-order Chebyshev bandpass filter centered at 94 GHz, which can be easily fabricated by state-of-the-art stereolithographic (SLA) 3D-printing techniques followed by silver coating, is shown. Excellent measured performance has been obtained.